Sign In to join the community | Help
Build & Remodel

Need help with ramp for wheelchair entry into apartment!

 I am at a loss, I have been confined in wheelchairs for years due to an auto wreck. I have just spent the last-6 weeks in hospital and rehab and found out I need to move soon.  I found a place to move to that will allow me to use the local para-transit vans, but I need to have a ramp built from the sidewalk up to the patio to be able to move in there.  Help really is needed please.  This ramp needs to be 10 feet long, 36-40 inches wide.  I have an estimate of $800.00, but I need to know what materials I would need to get so that it complies with both the ADA and Missouri guidelines.  I need to get the information soon as I need to move by Nov 26th.  Can anyone help me out?  Is there some place I can get help obtaining the materials or funds for labor in the Kansas City area?   

 

Thanks

Sharon

Not what you were looking for ? Try posting a question
Posted 2012-10-26T22:42:02+0000  by syjones771 syjones771
 

Here are the ADA guidelines for Ramps (ADAAG Section 4.8, as amended through 9/2002)

 

 

4.8 Ramps.

4.8.1* General. Any part of an accessible route with a slope greater than 1:20 shall be considered a ramp and shall comply with 4.8.

4.8.2* Slope and Rise. The least possible slope shall be used for any ramp. The maximum slope of a ramp in new construction shall be 1:12. The maximum rise for any run shall be 30 in (760 mm). Curb ramps and ramps to be constructed on existing sites or in existing buildings or facilities may have slopes and rises as allowed in 4.1.6(3)(a) if space limitations prohibit the use of a 1:12 slope or less.

4.8.3 Clear Width. The minimum clear width of a ramp shall be 36 in (915 mm).

4.8.4* Landings. Ramps shall have level landings at bottom and top of each ramp and each ramp run. Landings shall have the following features:

(1) The landing shall be at least as wide as the ramp run leading to it.

(2) The landing length shall be a minimum of 60 in (1525 mm) clear.

(3) If ramps change direction at landings, the minimum landing size shall be 60 in by 60 in (1525 mm by 1525 mm).

(4) If a doorway is located at a landing, then the area in front of the doorway shall comply with 4.13.6.

4.8.5* Handrails. If a ramp run has a rise greater than 6 in (150 mm) or a horizontal projection greater than 72 in (1830 mm), then it shall have handrails on both sides. Handrails are not required on curb ramps or adjacent to seating in assembly areas. Handrails shall comply with 4.26 and shall have the following features:

(1) Handrails shall be provided along both sides of ramp segments. The inside handrail on switchback or dogleg ramps shall always be continuous.

(2) If handrails are not continuous, they shall extend at least 12 in (305 mm) beyond the top and bottom of the ramp segment and shall be parallel with the floor or ground surface.

(3) The clear space between the handrail and the wall shall be 1 - 1/2 in (38 mm).

(4) Gripping surfaces shall be continuous.

(5) Top of handrail gripping surfaces shall be mounted between 34 in and 38 in (865 mm and 965 mm) above ramp surfaces.

(6) Ends of handrails shall be either rounded or returned smoothly to floor, wall, or post.

(7) Handrails shall not rotate within their fittings. 

4.8.6 Cross Slope and Surfaces. The cross slope of ramp surfaces shall be no greater than 1:50. Ramp surfaces shall comply with 4.5.

4.8.7 Edge Protection. Ramps and landings with drop-offs shall have curbs, walls, railings, or projecting surfaces that prevent people from slipping off the ramp. Curbs shall be a minimum of 2 in (50 mm) high.

4.8.8 Outdoor Conditions. Outdoor ramps and their approaches shall be designed so that water will not accumulate on walking surfaces.

Posted 2012-11-05T16:10:43+0000  by Paul
 
Not what you were looking for ? Try posting a question

Topic
Categories+